When we handle pressure washing for asphalt in Meridian, ID, it comes down to three things: protecting your plants and property, cleaning with the right method, and walking the job with you at the end. With asphalt, the right approach is low-to-moderate pressure wash.
How we clean it
Cleaning solution: An asphalt-safe degreaser; avoid solvent-based products.
What to know about cleaning asphalt
Asphalt is softer than concrete and is held together by its binder, so it is washed at lower pressure. Washing removes dirt and some oil staining before sealcoating, but old, absorbed oil stains rarely disappear completely.
Avoid: High pressure and harsh solvents that loosen the aggregate and break down the binder.
How often: Before sealcoating, typically every 2-3 years.
Is it time for pressure washing for asphalt?
- Driveway or walkways look dark, gray or streaky
- Green or black growth in shaded areas and along edges
- Slippery surfaces after rain
- Oil, rust or tire marks you can't scrub out
- You're getting ready to sell, seal or paint
What causes the dirt and stains
- Dirt and pollen that settle into the pores of concrete
- Mold, mildew and algae in damp, shaded spots
- Oil and fluid drips from vehicles
- Rust from sprinklers, furniture and fertilizer
- Tire marks and general foot traffic
What you can do yourself
- Sweep off leaves and loose debris so they don't stain
- Blot fresh oil drips with cat litter or an absorbent right away
- Point sprinklers away from walls and walkways to cut down on rust and hard-water stains
- Rinse pollen off with a garden hose during heavy pollen season
Not sure what you're looking at? The free stain identifier and safe pressure guide explain each stain and surface.
Common mistakes to avoid
- Etched lines and 'zebra stripes' from holding a narrow tip too close
- Water forced into window frames, door sills and siding laps
- Damaged plants and lawns from chemical runoff
- Injuries: a zero-degree tip can cut skin, and wet surfaces are slippery
What happens on the day
- Walk the property and note surfaces, stains and anything fragile
- Protect plants, outlets, lights and doors, and move small items
- Pre-treat organic growth and degrease oil spots
- Clean with the right pressure and a surface cleaner for even results
- Rinse, post-treat to slow regrowth, and walk the job with you
How much does pressure washing for asphalt cost?
What moves the price:
- Size: square footage of siding, roof or flatwork
- Condition: heavy growth, old stains and peeling finishes take longer
- Access: number of stories, roof pitch, slopes and how close we can park
- Add-ons: sealing, gutter brightening and other services done in the same trip
These are typical U.S. ranges, not a quote. You get an exact price before any work starts. For a quick estimate, try the pressure washing cost calculator.
Other services for asphalt
Pressure Washing for Asphalt in Meridian, ID
Snow, deicing salt and freeze-thaw cycles wear Idaho concrete. Cleaning it in spring and sealing it in late summer helps prevent surface flaking.
We provide pressure washing for asphalt across Meridian (ZIP codes 83642, 83646 and 83680) and nearby towns including Eagle (6.1 mi), Star (7.5 mi), Garden City (7.7 mi) and Kuna (8.4 mi). Call (555) 010-0000 for a free quote in Meridian.
Pressure Washing for Asphalt: frequently asked questions
How much does pressure washing for asphalt cost in Meridian, ID?
Pressure Washing for Asphalt typically costs $150-$600 for a typical home's driveway, walkways and patio, and usually takes 1-4 hours. The exact price depends on the size and condition, and you get it before any work starts. Call (555) 010-0000 for a free quote.
Do you use high pressure for pressure washing for asphalt?
For asphalt: usually 1,500-2,500 PSI; hot water helps with oil. What we avoid: high pressure and harsh solvents that loosen the aggregate and break down the binder. The cleaning solution does most of the work, followed by a gentle rinse.
Is pressure washing for asphalt safe for my plants and pets?
We pre-wet plants and lawns, keep cleaning solutions diluted to what the surface needs, and rinse landscaping again when we finish. Keep pets and children inside until surfaces are rinsed and dry.
How often should I schedule pressure washing for asphalt?
Before sealcoating, typically every 2-3 years. Shade, nearby trees, humidity and heavy traffic mean more frequent cleaning; sunny, dry spots can go longer. Our free cleaning frequency tool gives a recommendation for your climate.
What if it rains on the day?
Light rain doesn't stop most washing, but heavy rain, high wind, lightning and freezing temperatures do. If the weather isn't right, we reschedule at no charge. Our work is backed by a satisfaction guarantee.